**Job Description** Exciting role for a Machinist who is looking to expand creativity and collaborate on new product introduction. To perform this job successfully, an individual must be able to perform each Key Responsibility and Functional Knowledge listed below satisfactorily. Analyze specifications, setup and operate machine tools, fit and assemble parts, fabricate and/or repair mechanical assemblies, build fixtures and jigs needed to perform specific tasks. Must be able to follow directions and work with limited supervision. Must be willing to work with and draw on the strengths of teammates. Must observe all company policies and procedures, including safety rules and OSHA regulations and maintain a clean and orderly work area. Must be physically and medically qualified to wear required personal protective equipment as prescribed under OSHA standards. While performing the duties of this job, the employee is regularly required to stand/walk/use hands to handle or feel/reach with hands and arms/climb or balance/stoop/knell/crouch or crawl/and talk or hear. The employee is occasionally required to sit. Sets up and operates manual and CNC machines. Capabilities to include programming CNC machines along with editing pre-programmed parts as needed. Meets standard times on routers and reports to supervisor when deviating from standard time. **This is a first shfit position working a 4/10 schedule: Mon-Thurs. 5:30am-4:00pm** Reports to supervisor any conflict or problem that will interrupt the flow of work in the Machine Shop work environment. The employee will be required to maintain good housekeeping, safety, and organizational habits. At the end of each work shift the employee is required to clean his/her machine and the immediate floor area around the machine. Employee will be required to clean on a rotating basis with other employees, other areas of the shop and machinery that are less susceptible to chip build-up but do require less frequent cleaning. (ex. cutoff saws) All community tooling should be placed back in its proper storage location for the next person s use. **Required Education, Experience, & Skills** High school or GED Vocational school or associates degree 5 years relevant experience. Has the ability to analyze a 3D Model using manufacturing software Has 3-5 years experience with CNC set up/machining. Be able to communicate drawing features and/or functionality/manufacturability with Engineering/Designers Experience reading and comprehending instructions, short correspondence, and memos. Experience writing correspondence and reports. Prior experience effectively presenting information in one-on-one and small group situations before customers, clients, or other employees. Apply concepts such as fractions, percentages, ratios, and proportions to practical situations. Thorough knowledge to Machine Shop mathematics. Ability to apply common sense understanding to carry out instructions furnished in written, oral, or diagram form. Ability to deal with problems that may arise in certain situations. Must be able to tour all work sites. Reads blueprints, sketches, drawings, manuals and specifications to determine dimensions and tolerances of finished part, sequence of operations, and setup and tooling requirements. Demonstrates set-up and thought process for sequence of operations. Measures, marks, and scribes dimensions and reference points on material or work piece as guides for the layout of subsequent machining. **Preferred Education, Experience, & Skills** Skilled operating manual and CNC machines with limited supervison. Mastercam/Creo programming experience. **Pay Information** Full-Time Salary Range: $66017 - $105628 Please note: This range is based on our market pay structures. However, individual salaries are determined by a variety of factors including, but not limited to: business considerations, local market conditions, and internal equity, as well as candidate qualifications, such as skills, education, and experience. Employee Benefits: At BAE Systems, we support our employees in all aspects of their life, including their health and financial well-being. Regular employees scheduled to work 20 hours per week are offered: health, dental, and vision insurance; health savings accounts; a 401(k) savings plan; disability coverage; and life and accident insurance. We also have an employee assistance program, a legal plan, and other perks including discounts on things like home, auto, and pet insurance. Our leave programs include paid time off, paid holidays, as well as other types of leave, including paid parental, military, bereavement, and any applicable federal and state sick leave. Employees may participate in the company recognition program to receive monetary or non-monetary recognition awards. Other incentives may be available based on position level and/or job specifics. **CNC Machinist IV** **122133BR** EEO Career Site Equal Opportunity Employer. Minorities . females . veterans . individuals with disabilities . sexual orientation . gender identity . gender expression